Rolling bearing
 
1. When mounting the SKF bearing, http://www.bearing-a.com/SKF/   the force should be evenly distributed, and cannot be directly hammered.
Such as: cooperate with interference is bigger, bearing should be placed on automatic temperature control of air heating furnace or oil furnace, heating temperature control strictly under 120 °.
 
2. Equipped with nylon cage bearing to under - 40 °, 120 ° long-term continuous stable work, work should not be more than 4 hours at 150 °, the transient temperature peak of up to 180 °.
 
3. The storage of the bearing should be cleaned, dry and not stored in a warehouse with chemical products. The relative humidity should not exceed 65%, and the bearing shall not be stored on the floor.
 
 
 
 
Deep groove ball bearing
 
1. When mounting the bearing, the force should be evenly distributed, and cannot be directly hammered.
Such as: cooperate with interference is bigger, bearing should be placed on automatic temperature control of air heating furnace or oil furnace, heating temperature control strictly under 120 °.
 
2. Equipped with nylon cage bearing to under - 40 °, 120 ° long-term continuous stable work, the work should not be more than 4 hours at 150 °, short peak temperature should not exceed 180 °.
 
3. The storage of the bearing should be cleaned, dry and not stored in a warehouse with chemical products. The relative humidity should not exceed 65%, and the bearing shall not be stored on the floor.
 
4. The inventory bearing should be cleaned again every other year for anti-rust packaging.
 
 
 
 
 
Angular contact ball bearings.
 
1. When mounting the bearing, the force should be evenly distributed, and cannot be directly hammered.
Such as: cooperate with interference is bigger, bearing should be placed on automatic temperature control of air heating furnace or oil furnace, heating temperature control strictly under 100 °.
 
2. Equipped with nylon cage bearing to under - 40 °, 120 ° long-term continuous stable work, the work should not be more than 4 hours at 150 °, the transient temperature peak of up to 180 °.
 
3. The storage of the bearing should be cleaned, dry and not stored in a warehouse with chemical products. The relative humidity should not exceed 65%, and the bearing shall not be stored on the floor.
 
 
 
 
 
Aligning roller bearing.
         
1. The user shall select the appropriate coordination and bearing strength to the clearance in accordance with the requirements. Please check the bearing code after unpacking.
 
2. Before bearing installation, the grease must be clean and appropriate when adding grease to the bearing.
 
3. In the case of installation, the outer ring end and roller should not be directly hit, so as not to break the inner circle or the middle and small side.
Often users should put the bearing into the mineral oil in heated to 90 ° to 100 ° immediately when loaded on the spindle.
Do not use the local spray method to the bearing, the user should also use the special sleeve to install when it is difficult to "hot install".
 
4. The bearing shall have a good sealing and dustproof device and lubrication, and cannot break oil.
 
5. Bearing storehouse should be clean and dry, without environmental pollution, bearing stacking, and packing without damage.
Bearings with excess of 1 year in stock must be cleaned and coated.
 
 
                   
 
Thrust roller bearing.
 
1. When installing the bearing, clean the bearing oil seal and clean the high quality lubricating oil.
 
2. When the bearing is installed, it shall be uniform and not hammer.
Such as the interference fit is larger, should put the bearing into the mineral oil in heated to 90 ° to 100 °, the installation immediately.
 
3. The storage room for bearing should be clean, clean and relative humidity not exceeding 65%.
 
4. The stock bearings should be cleaned and coated once every other year, and the oil seal packaging is kept in good condition.
 
When using the bearing, it should have a good sealing and dustproof device, and should check the working condition frequently.
 
 
 
Cylindrical roller bearings.
 
1. The bearing is separated, and the user can adjust the clearance according to the need when installing.
 
2. Before use, the bearing shall be cleaned with gasoline or kerosene and kept well lubricated.
 
3. When the bearing is installed, the bearing should be pressed into the part, and no tapping is allowed.
 
4. Bearing storage should be clean and ventilated to avoid damp, bearing should be kept for a long time, and should be rustproof regularly.
 
 
 
 
Thrust ball bearing
 
1. The bearing seal should be removed when installing the bearing, and clean and clean the high quality lubricating oil.
 
2. When the bearing is installed, it shall be uniform and not hammer.
Such as the interference fit is larger, should put the bearing into the mineral oil in heated to 90 ° to 100 °, the installation immediately.
 
3. The storage room for bearing should be clean, clean and relative humidity not exceeding 65%.
 
4. The stock bearings should be cleaned and coated once every other year, and the oil seal packaging is kept in good condition.
 
When using the bearing, it should have a good sealing and dustproof device, and should check the working condition frequently.